 |
T-shirt Press 38 x 38 cm | |||
|
|
T-shirt press 38 x 38 cm with upper lever closing. It has a robust mechanical construction with vertically adjustable heater. You can print following items ( from our offer ):. T-shirts - Kidīs / Womenīs / Menīs / Running / Bike Cushions - Fine structure / Satin / Soft / Linen Pads - Bar / Table / Floor / Mouse Bags - Shopping / Toiletry Backpacks - School / Shoulder / Jeans Aprons - Fine structure / Linen Caps Bibs Puzzle A5 - A3 Coaster with or without cork MDF boards Flat ceramics / sublimation stones ( printing ceramics and all products that may not be perfectly flat and are also fragile, we recommend printing in 3D Press ) The digital electronic unit measures time (adjustable 0 - 999sec) and controls the temperature of the heating element (adjustable 0 - 225 C). Settings are made simply using the cursor keys. |
|
||
e-shop /
38x38  |
||||
|
Liberek spol. s r.o. - Liberek spol. s r.o. - Liberek spol. s r.o. - Liberek spol. s r.o - Liberek spol. s r.o. - Liberek spol. s r.o. - Liberek spol. s r.o -- Liberek spol. s r.o. - Liberek spol. s r.o. - Liberek |
||||
| Specific features | ||||
|
|
||||
|
|
UNPACKING THE T-SHIRT PRESS
The press is packed in 2 cardboard boxes and is additionally fixed with screws on the lower wooden transport plate. It is best to open the lids of both boxes, remove the top wooden board and carefully turn the entire press on its side. Subsequently, pull the entire press to the side, including the foam fillings After taking it out of the box, unscrew the bottom wooden plate and and screw instead the rubber feet, which are separately in the box. Place the press on its feet, remove the foam fillings, cut the fixing tapes that hold the press closed and carefully unpack the 220V cable The power of the press is 1800W, so connect the press separately (not via multiple socket) to a 220V socket. |
|||
|
PRESSURE ADJUSTMENT |
! If you are not
using the press, always not only switch it off, but also disconnect it from
the mains (e.g. by pulling it out of the socket !
PRESSURE ADJUSTMENT With the press turned off, adjust the pressure according to the thickness of the printed object. The press enables the printing of objects with a maximum thickness of 6 mm Adjust the press by turning the rose (nut) as shown on th picture. Make sure that after setting the press has the pressure you want. The press has an AUTO-OPEN function, i.e. it does not hold in the closed position when the press is switched off. If the press is switched on after closing, the electromagnet is activated, which attracts the metal pad fixed to the handle and thus holds the press in the closed position 
 |
|||
|
TEMPERATURE TIME / SETTING
|
TEMPERATURE TIME / SETTING Plug the press into the socket. The power consumption of the press is approx. 1800W, i.e. use a socket in which no other appliance is already connected. Turn the press on with the rocker switch and set the temperature / time if needed. The default on the press is 180 C / 60 sec Please check the e-shop before printing, where there are recommended temperatures / times for each printable item Control unit settings : * press the OK button 1 x and select the Celsius / Farnheit scale with the up / down cursor button * press the OK button 2 x and select the default temperature (180C) with the up / down cursor button It is not recommended to use a temperature higher than 200C * press the OK button 3 x and select the default time ( 60 sec ) with the up / down cursor button 
 |
|||
|
PRINTING |
PRINTING After setting the temperature and time, the press starts to heat up. If the temperature reaches the set value, the user is notified acoustically that he can start printing. Place the object on the base plate with the image fixed to the object to be printed and place a Teflon cover over the top and close the press. Just before the set time expires, an acoustic signal sounds, even before the press opens automatically. Please note, automatic release means that the electromagnet holding the lever is turned off = the lever jumps up and only then the gas struts engage so that the press opens in a cultured manner in the second half of its stroke. You can stop printing at any time by pressing the red emergency button, which releases the electromagnet and the press opens 
 |
|||
| Technical specifications | ||||
|
|
||||
| Functions | Digital adjustment of temperature and time, adjustable pressure, AUTO-OPEN feature | |||
| Operat. conditions | Temperature 5 do + 400 C | |||
| Power requirements | 110 / 220V, 50Hz, max 1.800 W | |||
| Dimensions (WxHxD) | 430 x 760 x 510 mm | |||
| Weight | 40 kg | |||
| Color | Black / red | |||
| Accessories | Mains cord | |||
| Certification | CE certificate | |||
|
T-shirt Press 38 x 38 |
eshop T-shirt Press 38x38 | |||
|
|
||||
| Stock spare parts | eshop spare parts | |||
