Mug press BJ880
			BJ880 is full wrap around press for Photo Ceramics with sturdy mechanical design. Mug press is supplied with 2 heaters  (in price), heat pad is inserted inside metal sleeve and power cable is terminated with connector, all for very easy and fast exchange of heat pad acc. to type (size) of ceramics which is printed. Digital electronic unit controls time (range 0 - 999 sec) and temperature, (range 90 - 220 C), initial setting is done very simply by the help of three buttons on membrane keyboard. Mug press is equipped with standard size of heat pad for Mugs (diameter 80-87mm) : STANDARD (white, colored handle nad rim, color changing Mugs ...) BIG (white, colored handle nad rim) STEIN ( Stein narrow, Stein glass matt)   Thicker heat pad is part of standard accessory (diameter 70-75mm) : Espresso / Mug Narrow
E-shop
Mitsubishi Electric technology for life - Mitsubishi Electric technology for life - Mitsubishi Electric technology for life - Mitsubishi Electric technology for life - Mitsubishi Electric technology for life
Specific features
Procedure			Mugs printing procedure ( standard Mug Press ) 1  Print a mirror image ( for example on Ricoh , Epson printer ) - pls note, you need to use only special sublimation ink ! 2  Fix the image on a Mug with 2 small pieces of adhesive heat resistant fixing tape If temperature / time is set on Mug press  ( see next chapter )    .. switch ON the Mug Press and wait until press is heated to BASIC TEMPERATURE ( Mug press indicates readiness with an occasional beep ) 3  Put Mug incl. image from side into open Mug press, close lever and press button with icon "square" on membrane keyboard. If you put cold mug into heat pad, temperature goes down as cold Mug is cooling heater, but after short time temperature gradually climb up to WORKING TEMPERATURE when the press automatically switches to time countdown. Display is showing remaining time and finally Mug Press issues audio signal - finish sublimation cycle by pressing " square" button, open the lever and remove Mug from Mug Press ( switch off Mug Press ) 4  Peel off the image gently with your fingernail from Mug and let Mug to cool RECOMMENDED / TIPS : * When you load Mug from the side into Mug Press, be carefull not to accidently bend corner of the image on heating pad. * Since ear cup remains cold over the whole heating cycle at the Mug Press, you can remove the Mug from Mug Press immediately after the completion of the cycle and to check quality of imprinting - gently bend the corners of still fixed image and make sure that underneath of all corners is the same contrast and saturation of colors - if not ( owing to low pressure or ... ) - rotate with Mug about 180 degrees and put it in the press again and repeat the cycle * If you are going to peel off  the image from Vow Mug (color change Mug) be very careful, because this coating is very soft at hot state and you can easily break through the top layer - there may remain permanently visible white scratches from your fingernail. Better remove the image after partial cooling cup.
Electronic unit			Setting of basic / working temperature and time The press purchased from us has correctly adjusted electronics unit, but if you need to change temperature / time (another type of ceramic / another kind of coating), please do the following : BASIC TEMPERATURE SETTING Press 1x button MODE (SET light is ON) =  default 90 C ( 140 set by us ) Using button "plus" and "minus" you can set basic temperature.  If you set 140 C / 250 F, Mug press is allways ready when you have more Mugs to print ( if the press is not in use, pls turn it off ) WORKING TEMPERATURE SETTING Press 2x button MODE (SET + TEMP light ON) = 160 - 170C* / 320 F Using button "plus" and "minus" set working temperature acc. to type of ceramics / coating. TIME SETTING Press 3x button MODE (SET + TIME light ON) = 40 (sec) * Using button "plus" and "minus" set heating time ( Mug will be heated on 170C for 40 seconds ). ( Last set values are immediately memorized ) Press 4x button MODE - original status, display is showing current temperature of heater. RECOMMENDED / TIPS : * Lower basic temperature reduces the thermal shock which absorbs ceramics during insertion into a heated press. This is especially important for products made of glass (risk of breakage in case of uneven heating) * It is recommended to tune step by step ideal working temperature to a particular type of Mug press and ceramics, which will be printed.  Individual Mug Presses ( similair in appearance ) may have different types of temperature sensors as well calibration -- the recommended values ( time / temperature ) given here are valid ONLY for MUg Press BJ880 / BJ900 and the ceramic we supply ( coating Orca ).   There is a simple rule to set correct working temperature - if you have low contrast colors on printed Mug, but contrast colors stood on sublimation paper - increase the temperature ( sublimation paper must visibly " washed-out " after printing cycle)  Just on the contrary - if sublimation paper is sticking to surface of Mug, sublimation paper gets yellowish and black color is turning into brown, Mug is overheated - decrease temperature. * If you print on a subject that doesnt have similair thermal inertia like ceramics - for example metal thermos or mug polymer, temperature rises from basic to the working temperature very quickly - you have to prolong time to about 90 - 120sec ( please, see eshop, where is recommended time / temperature to each product )
Technical specifications
El schema
Functions			digital adjustment of temperature and time, adjustable diameter and pressure
Operat. conditions			temperature 5 do + 400 C
Power requirements			220V, 50Hz, 350W
Dimensions (WxHxD)			300 x 310 x 270 mm
Weight			9 kg
Color			black
Certification			CE
BJ880			151,60 EUR (Export price without VAT)
Options :
Heat Pad BJ880    standard size			31,60 EUR  spare heater for Mugs standard size
Heat Pad BJ880    shorter size			31,60 EUR  shorter heater for Espresso / Mug Narrow
Ceramics : (Mug press BJ880)			Mugs    Glass   Steins    Glass Stein